Engelseruiter

h1. Esphome

{{>toc}}

h2. TTGO T-Journal

The T-journal is able to communicate the battery state over i2c. After bridging the pads as shown in the picter the IP5306 that is used is connected to pins 13 (scl) and 14 (sda). 

!clipboard-202303271732-dyvee.png!

working configuration:

<pre>

substitutions:

  device_name: "cam01"

esphome:

  name: '${device_name}'

esp32:

 board: esp32dev

 framework:

   type: arduino

# Enable Home Assistant API

api:

  encryption:

    key: "xxxxxxxxxxxx"

ota:

  password: "xxxxxxxxxxxxx"

wifi:

  ssid: !secret wifi_ssid

  password: !secret wifi_password

  # Enable fallback hotspot (captive portal) in case wifi connection fails

  ap:

    ssid: "cam01 Fallback Hotspot"

    password: "xxxxxxx"

captive_portal:

external_components:

  - source:

      type: git

      url: https://github.com/MichaKersloot/esphome_custom_components

    components: [ ip5306, esp32_camera ]

i2c:

  - id: bus_a

    sda: 14

    scl: 13

    frequency: 400kHz

    scan: true    

ip5306:

  battery_level:   # sensor

    name: '${device_name} - Battery Level'

  charger_connected:  # binary_sensor

    id: connected

    on_press:

      then:

        - lambda: ESP_LOGD("TEST", "charging");

    on_release:

      then:

        - lambda: ESP_LOGD("TEST", "not charging");

  charge_full:  # binary_sensor

    id: full

    on_press:

      then:

        - lambda: ESP_LOGD("TEST", "fully charged");

    on_release:

      then:

        - lambda: ESP_LOGD("TEST", "still charging");

esp32_camera:

  name: '${device_name} - camera'

  external_clock:

    pin: GPIO27

    frequency: 20MHz

  i2c_pins:

    sda: GPIO25

    scl: GPIO23

  data_pins: [GPIO17, GPIO35, GPIO34, GPIO5, GPIO39, GPIO18, GPIO36, GPIO19]

  vsync_pin: GPIO22

  href_pin: GPIO26

  pixel_clock_pin: GPIO21

  agc_gain_ceiling: 8x

  # jpeg_quality: 16

  # max_framerate: 25Hz

  contrast: 0

  brightness: 1

  saturation: 0

  ae_level: 2

  # aec2: True

  horizontal_mirror: false

  vertical_flip: false

  resolution: 800x600

esp32_camera_web_server:

  - port: 8080

    mode: stream

  - port: 8081

    mode: snapshot

</pre>

If you are unable to program:

  python -m esptool --chip esp32 --port COM5 --baud 115200 --after hard_reset erase_flash

and if even that doesn't solve it:

  python -m esptool --port COM5 write_flash_status --non-volatile 0

h2. p1 dsmr power meter with TTGO T7 v1.3 mini

more on: https://github.com/LilyGO/TTGO-T7-Demo

I'm using a TTGO T7 v1.3 mini and a piece of a dutch phone cable with an RJ11 connector. I soldered the cable directly on the board.

!clipboard-202304142146-wfydy.png!

On RJ11, pin 1 and pin 6 are not connected / available

|_.RJ11 P1|_.ESP32 Pin|_.4w cable|_.comments|

|2 - CTS|GPIO19|black|Clear to Send, High = allow P1 Meter to send data|

|3 - Data GND|GND|red||

|4 - nc|-|green||

|5 - RXD (data)|GPIO16|yellow|1K external pull-up resistor needed|

!clipboard-202304142208-kcypl.png!

Working configuration:

<pre>

substitutions:

  name: p1meter

  friendly_name: p1meter

esphome:

  name: ${name}

  friendly_name: ${friendly_name}

esp32:

  board: ttgo-t7-v13-mini32

  framework:

    type: arduino

# Enable logging

logger:

  # Serial logging is disabled by setting the logger baud rate to 0.

  # Otherwise the logger will occupy the hardware UART, making it unavailable

  # for receiving smart meter data on pin D7 (GPIO13).

  baud_rate: 0

# Enable Home Assistant API

api:

  encryption:

    key: "xxxxxxxxxxxxxxxxxxxx"

ota:

  password: "xxxxxxxxxxxxxxxxxxxxx"

wifi:

  ssid: !secret wifi_ssid

  password: !secret wifi_password

  # Enable fallback hotspot (captive portal) in case wifi connection fails

  ap:

    ssid: "P1Meter Fallback Hotspot"

    password: "xxxxxxxxxxxxx"

captive_portal:

uart:

  id: uart_bus

  rx_pin:

    number: GPIO16

    inverted: true

  baud_rate: 115200

  rx_buffer_size: 1700

dsmr:

  request_pin: GPIO19

sensor:

  - platform: dsmr

    energy_delivered_tariff1:

      name: Energy Delivered Tariff 1

      state_class: total_increasing

    energy_delivered_tariff2:

      name: Energy Delivered Tariff 2

      state_class: total_increasing

    energy_returned_tariff1:

      name: Energy Returned Tariff 1

    energy_returned_tariff2:

      name: Energy Returned Tariff 2

    power_delivered:

      name: Power Consumed

    power_returned:

      name: Power Returned

    electricity_failures:

      name: Electricity Failures

    electricity_long_failures:

      name: Electricity Long Failures

    voltage_l1:

      name: Voltage L1

    voltage_l2:

      name: Voltage L2

    voltage_l3:

      name: Voltage L3

    current_l1:

      name: Current L1

    current_l2:

      name: Current L2

    current_l3:

      name: Current L3

    power_delivered_l1:

      name: Power Delivered L1

    power_delivered_l2:

      name: Power Delivered L2

    power_delivered_l3:

      name: Power Delivered L3

    power_returned_l1:

      name: Power Returned L1

    power_returned_l2:

      name: Power Returned L2

    power_returned_l3:

      name: Power Returned L3

    gas_delivered:

      name: Gas Delivered

text_sensor:

  - platform: dsmr

    identification:

      name: Identification

    p1_version:

      name: Version

</pre>

!clipboard-202304142159-fj2tf.png!