Esphome¶

• Inhoudsopgave
• Esphome
  • TTGO T-Journal
  • p1 dsmr power meter with TTGO T7 v1.3 mini

TTGO T-Journal¶

The T-journal is able to communicate the battery state over i2c. After bridging the pads as shown in the picter the IP5306 that is used is connected to pins 13 (scl) and 14 (sda).

working configuration:

substitutions:
  device_name: "cam01" 

esphome:
  name: '${device_name}'

esp32:
 board: esp32dev
 framework:
   type: arduino

# Enable Home Assistant API
api:
  encryption:
    key: "xxxxxxxxxxxx" 

ota:
  password: "xxxxxxxxxxxxx" 

wifi:
  ssid: !secret wifi_ssid
  password: !secret wifi_password

  # Enable fallback hotspot (captive portal) in case wifi connection fails
  ap:
    ssid: "cam01 Fallback Hotspot" 
    password: "xxxxxxx" 

captive_portal:

external_components:
  - source:
      type: git
      url: https://github.com/MichaKersloot/esphome_custom_components
    components: [ ip5306, esp32_camera ]

i2c:
  - id: bus_a
    sda: 14
    scl: 13
    frequency: 400kHz
    scan: true    

ip5306:
  battery_level:   # sensor
    name: '${device_name} - Battery Level'
  charger_connected:  # binary_sensor
    id: connected
    on_press:
      then:
        - lambda: ESP_LOGD("TEST", "charging");
    on_release:
      then:
        - lambda: ESP_LOGD("TEST", "not charging");
  charge_full:  # binary_sensor
    id: full
    on_press:
      then:
        - lambda: ESP_LOGD("TEST", "fully charged");
    on_release:
      then:
        - lambda: ESP_LOGD("TEST", "still charging");

esp32_camera:
  name: '${device_name} - camera'
  external_clock:
    pin: GPIO27
    frequency: 20MHz
  i2c_pins:
    sda: GPIO25
    scl: GPIO23
  data_pins: [GPIO17, GPIO35, GPIO34, GPIO5, GPIO39, GPIO18, GPIO36, GPIO19]
  vsync_pin: GPIO22
  href_pin: GPIO26
  pixel_clock_pin: GPIO21
  agc_gain_ceiling: 8x
  # jpeg_quality: 16
  # max_framerate: 25Hz
  contrast: 0
  brightness: 1
  saturation: 0
  ae_level: 2
  # aec2: True
  horizontal_mirror: false
  vertical_flip: false
  resolution: 800x600

esp32_camera_web_server:
  - port: 8080
    mode: stream
  - port: 8081
    mode: snapshot

If you are unable to program:

python -m esptool --chip esp32 --port COM5 --baud 115200 --after hard_reset erase_flash

and if even that doesn't solve it:

python -m esptool --port COM5 write_flash_status --non-volatile 0

p1 dsmr power meter with TTGO T7 v1.3 mini¶

I'm using a TTGO T7 v1.3 mini and a piece of a dutch phone cable with an RJ11 connector. I soldered the cable directly on the board.

On RJ11, pin 1 and pin 6 are not connected / available

RJ11 P1	ESP32 Pin	4w cable	comments
2 - CTS	GPIO19	black	Clear to Send, High = allow P1 Meter to send data
3 - Data GND	GND	red
4 - nc	-	green
5 - RXD (data)	GPIO16	yellow	1K external pull-up resistor needed

Working configuration:

substitutions:
  name: p1meter
  friendly_name: p1meter

esphome:
  name: ${name}
  friendly_name: ${friendly_name}

esp32:
  board: ttgo-t7-v13-mini32
  framework:
    type: arduino

# Enable logging
logger:
  # Serial logging is disabled by setting the logger baud rate to 0.
  # Otherwise the logger will occupy the hardware UART, making it unavailable
  # for receiving smart meter data on pin D7 (GPIO13).
  baud_rate: 0

# Enable Home Assistant API
api:
  encryption:
    key: "xxxxxxxxxxxxxxxxxxxx" 

ota:
  password: "xxxxxxxxxxxxxxxxxxxxx" 

wifi:
  ssid: !secret wifi_ssid
  password: !secret wifi_password

  # Enable fallback hotspot (captive portal) in case wifi connection fails
  ap:
    ssid: "P1Meter Fallback Hotspot" 
    password: "xxxxxxxxxxxxx" 

captive_portal:

uart:
  id: uart_bus
  rx_pin:
    number: GPIO16
    inverted: true
  baud_rate: 115200
  rx_buffer_size: 1700

dsmr:
  request_pin: GPIO19

sensor:
  - platform: dsmr
    energy_delivered_tariff1:
      name: Energy Delivered Tariff 1
      state_class: total_increasing
    energy_delivered_tariff2:
      name: Energy Delivered Tariff 2
      state_class: total_increasing
    energy_returned_tariff1:
      name: Energy Returned Tariff 1
    energy_returned_tariff2:
      name: Energy Returned Tariff 2
    power_delivered:
      name: Power Consumed
    power_returned:
      name: Power Returned
    electricity_failures:
      name: Electricity Failures
    electricity_long_failures:
      name: Electricity Long Failures
    voltage_l1:
      name: Voltage L1
    voltage_l2:
      name: Voltage L2
    voltage_l3:
      name: Voltage L3
    current_l1:
      name: Current L1
    current_l2:
      name: Current L2
    current_l3:
      name: Current L3
    power_delivered_l1:
      name: Power Delivered L1
    power_delivered_l2:
      name: Power Delivered L2
    power_delivered_l3:
      name: Power Delivered L3
    power_returned_l1:
      name: Power Returned L1
    power_returned_l2:
      name: Power Returned L2
    power_returned_l3:
      name: Power Returned L3
    gas_delivered:
      name: Gas Delivered

text_sensor:
  - platform: dsmr
    identification:
      name: Identification
    p1_version:
      name: Version